榴莲视频下载app

激光切割機作為新型的加工設備，因其加工精度高、光潔度良好、加工效率高所有近年來尤為受加工廠家歡迎，激光切割機的日常維護與保養也是很重要的，只有日常的保養維護工作做好了，激光切割機才能保持良好的穩定性，延長壽命。

激光切割機的維護與保養

1. 防塵與去塵：灰塵會使電器元件絕緣性能變壞而導致電擊穿，會使運動系統磨損加劇導致精度降低，會使光路系統出光變弱和不出光。平時要用抹布將設備外表擦洗干凈，用長毛刷和高壓氣槍對設備內部回城沖刷干凈。

2. 防熱與排熱：溫升會使設備絕緣性能下降，元器件參數變差。通常規定切割機工作環境不超過40℃，以20~25℃最為合適。

3. 防振與防松：切割機對振動特別敏感，工作環境應該選擇遠離有沖床、重物搬運等有振動源的場所，建議安裝防振墊，連接松動應重新加固。

4.防干擾與防漏電：切割機電磁環境主要包括周圍電磁場、供電電源品質、信號電氣噪聲干擾三個內容手機高頻信號有時也能干擾振鏡切割信號。

供電電源品質較好的電網頻率波動范圍為±0.5%，幅面波動范圍為5%~±10%，供電電源品質差時應該配置電源穩壓器或UPS電源。信號線和電源線之間、信號線與信號線之間有時會產生點或磁的耦合引起電氣噪聲干擾，如Q高頻信號線與振鏡信號線纏繞在一起，一般要將這兩根線拉開一定距離。切割機機殼接地不但能防止漏電危險，還能防止電網對設備的干擾如果客戶安裝環境沒有地線，則可以將一根1m以上扁平鐵打入室外地下當地線使用，在臨時應急使用時可將地線接到供水的鋼鐵管上使用。

電器元件維護保養知識

電氣元件主要是指限位開關、傳感器、操作按鈕、工作指示燈等。1、限位開關激光切割機至少每月檢查一次限位開關是否有效，步驟如下：啟動機器回零，使運動軸做極限位置運動，如果運動軸到達極限位置是停止運動，則證明限位開關工作正常；如果到達極限位置時還繼續運動，則說明限位開關已損壞。2、各按鈕及指示燈的維護斷開相關電氣連接后萬用表測量按鈕觸點接通及斷開動作是否正常，有意觸發各種工作和報警狀態，測試警示燈、信號指示燈是否正常。

以上就是激光切割機日常所需的維護與保養工作，想要進一步了解激光切割機可以關注我們，我們會持續為您更新更多激光切割機相關知識內容！